Shooting these in a Browning model 53 in lever action silhouette matches. Shoot great if I could only learn to squeeze the trigger!

I like the consistency of your bullets in size, weight, and lube. I've loaded several hundred but as yet haven't shot any of them. Only one problem, I got them for loading 327 ammo and in the Ruger Single 7 you have to watch the OAL and may end up crimping on the driving band so the cylinder will rotate. Other wise I'm very pleased with them and intend trying several other of your offerings in other calibers.

I’ve shot 2,000 rounds using the as an affordable option for the 32 H&R Magnum cartridge. They are extremely accurate and my go to bullet.

4gr of TiteGroup and my Ruger Single Seven with a 7in barrel puts these right on target.

No Leading, easy loading, and perfect snug fit in my cylinder chambers.

I am still working on loads, but for my 327 Fed Mag, these are the perfect bullet.

Haven't shot too many yet, but so far they shoot well. Plan on using them in the Western Levergun national silhouette matches at Raton this year.

Love everything about them. Great price. Seat easily and very accurate!

Shipping was super fast, bullets are first rate quality. Thank you BadMan!!

I have and still use both coated and standard bullets. Badman's quality and value can't be beat for one of best made cast bullets I found anywhere.

Shoot these out of a 32-20 Win/Miroku 24"92, 10 shot 2" group at 100 yards all day long. These are really nice bullets.

Consistent quality

Thank you Pat

This is the third time I have ordered these. Accurate and leave the barrel clean. Perfect for the shorter 32-20 brass.

I have loaded and shot several thousand of these bullets and am really pleased with them. The coating is excellent and does not chip or rub off. I think they are as good as any jacketed bullet in my firearms. Even at higher speeds they do not lead barrels. Really consistent in weight and are my go to bullet. Thanks for such a great product.

The crimp groove on these bullets allows me to make my ammo the correct length with shorter brass. Accuracy is right on.

Haven't loaded them yet but they look great, just like all the polymer bullets I receive from Badman. I expect them to shoot just as well as all the others.

I use these for my 32-20 and I really like them. They are a good fit for the shorter Starline and Winchester brass. The crimp groove allows for a full length cartridge, not .030 or .040 short.

Excellent service and quality products.

I like these bullets as they allow me to load them hotter without worrying about lead buildup. They also group pretty well. Also on the plus side, if you have any questions or need to contact Badman Bullets, they respond to questions in a very timely manner. 5 stars from me.

EZ reloading, Clean shooting , just like the other calibers I use
PLUS GREAT Customer service

Bullets are great. Poly coating is cleaner on hands and loading equipment. Shipping is free and fast!

I had contacted Badman Bullets about using their .32 100 grain coated bullets in my 327 revolvers at some very high muzzle velocities. The owner asked about the powders I was considering and sent me some recommended loads for MV's between 1200 fps and 1350 fps.

After comparing the results from 3 different powders I ended up selecting 5.4 grains of W231 powder to use with an OAL of 1.470".

I'm able to shoot 1" groups at the short ranges used in personnel defense practice using iron sights. Considering I'm 73 with very poor eyesight, I found this to be a good practice round.

I calculated the MV is 1220 fps with 320 ft.-lb. of ME. This is about 2/3 the power of my commercial 327 rounds which are rated at 1600 fps MV and 500 ft.-lb. ME. Not full power, but not a powder puff load.

I like the support Badman gave me in determining reasonable limits for the velocity this bullet would support in my application.

I've gone trough over a thousand rounds and have selected this bullet for most of my .32 caliber loads. I also use their 78 grain bullet, which gets the most use in my .32 S&W (short) and .32 S&W Long ammunition. It worked well in my 327, but I was looking at emulating my 100 grain commercial load as closely and cost effectively as possible.

I did find that Badman's bullet coating was heavier and more uniform then the same coating from other coated bullet manufacturers.

Based on this bullets performance and the owners support, Badman will be my coated bullet supplier for my handgun ammunition needs (.32, .38/.357, 9mm, and ,45 ACP).

Consistent weights and quality on every single bullet! Loaded into cases with ease. Best is no smoke at the range.

Have always been pleased with the Badman products and these coated bullets are just great!

Why pay more? The 100 gr polymer coated in my 32 H&R, 327 Federal with AAA+++ results. I also use thier.45-200swc, 124&147-9mm, 200-44.mag all polymer coated with great results. Less smoke, better accuracy. Well made great bullets and that goes for thier standard lubed bullets also and don't forget the free shipping.

Nice!

The bullets I use need to be consistent in size and weight, properly formed and coated, and reasonably priced. These bullets hit the bullseye I am very satisfied with their performance.

I load the 32 100 grain coated bullets for my wife to shoot in SASS events and they work flawlessly. I use coated bullets so I don't gum up my press and to lessen the effects of handling lead. They do the job when she does.

This is my third order from Badman. The bullets I've tried have been of very high quality and very tight consistency, which allows me to make my very best ammo. Badman's pricing is better than others of similar quality, so I'm a repeat customer.

Im very pleased with the 100 grain, .32 caliber polymer coated bullets I recently purchased from Babman Bullets. My order arrived within days and the bullets are fantastic. The best part is - With the polymer coating I don't have the worry of handling lead while reloading and lead fowling during shooting is non issue, they shoot so clean. Thanks Mike Stevens (SASS Kitsap Kid)

Finally was able to shoot a couple hundred out of a Ruger Single Six 32 Magnum and Ruger LCR .327 revolvers. They dont smoke or smell like other coated bullets. They are great bullets and load and shoot wonderfully.

Have not shot these yet. Have loaded up a few hundred. I use the same style/shape/weight/size and caliber of bullet from other manufactures as these that are not coated. Since I already have those loads dialed in Im just sticking with the same recipe to load these coated bullets. I have shot a few thousand Badman Bullets cast bullets and they were top notch just like these coated bullets. I did a smash test and the coating held up so Im expecting no problems with these hi tek coated bullets but when I shoot them if I run in problems I will update my review.

I bought these to load for my
granddaughter. I must say I do like the cleanliness of the polymer coated bullets.

These load and shoot great. This is a great alternative to lead, which I avoid. The only other alternative to lead in .32 Caliber is a limited selection of expensive FMJ, which is too expensive for plinking. Thank you for this offering. An 83g or 85g coated would be a welcomed addition too.

Cleaner, reload much easier, and cycle through Browning 53 lever gun much better than lead. I will never go back to lead bullets.